23:05
Half wave rectifier অর্ধতরঙ্গ একমুখী করণ।
Friday 7 August 2020
Thursday 2 July 2020
DSO138 oscilloscope with AC sign web measure.
AC sign web practical with dso138 oscilloscope
The new oscilloscope set from Joy- IT is the ideal companion for the ambitious layman. The DSO138 is the perfect complement to the formerly common multimeter, allowing you to measure and estimate time-dependent signals without having to invest in precious professional tackle. All introductory functions of a digital storehouse oscilloscope are included automatic/ homemade detector mode, single shot recording with signal analysis, restoration of stored signal characteristics. The set is assembled in no time at all The circuit board only has to be fitted into the screw suitable casing. No soldering or analogous work is needed.
Monday 8 June 2020
Dso138 oscilloscope
DSO138 was designed as a training oscilloscope kit. It contains only the basic oscilloscope functions with no fancy features. Simplicity in structure and easiness in assembly/operation are amongst the main highlights of the design. For these purposes, DSO138 uses mostly through-hole parts. The heart of DSO138 is a Cortex-M3 ARM processor (STM32F103C8) from ST. It uses a 2.4-inch TFT LCD (320 X 240 dotmatrix, 262K colors) that displays crisp and clear waveforms.
DSO138 is partially open-sourced. This opens the possibility for users to add different features or develop new applications on the hardware.
Major features of DSO138:
Analog bandwidth: 0 – 200KHz
Sensitivity: 10mV/Div – 5V/Div
Sensitivity error: lessthen 5%
Vertical resolution: 12-bit
Timebase: 10us/Div – 500s/Div
Record length: 1024 points
Built-in 1KHz/3.3V test signal
Waveform frozen (HOLD) function available
Save/recall waveform
How install CCS c pcw Compiler software .
install CCS c pcw Compiler software .
Email
admin@hellotech.com.bd
যারা মেইল করবে তারা মেইল করারা পর অবশ্বয় কমেন্ট করে জানাবে, তাহলে আমার জানতে সুবিধা হবে, আর পাওয়ার পর আবার কমেন্ট করে জানাবে যে পেয়েছ,
মেইল এর নাম আর ইউটিউব চ্যনেলের নাম যেন এক হয়, আর না হলে চ্যনেলের নামটি মেইলে বলে দেবে, নইত কমেন্টে,
আর যদি ইনবক্স এ না পাও তবে স্পাম এ মেইল পাবে,
আর বাকি কাজ গুলো করতে ভুলবেনা!
website
hellotech.com.bd
Every circuit how to work.
every circuit app how to work like Proteus software, after next tutorial will be make circuit by android every circuit app, electronic hobbyist try to this app, web site hellotech.com.bd email admin@hellotech.com.bd যারা মেইল করবে তারা মেইল করারা পর অবশ্বয় কমেন্ট করে জানাবে, তাহলে আমার জানতে সুবিধা হবে, আর পাওয়ার পর আবার কমেন্ট করে জানাবে যে পেয়েছ, মেইল এর নাম আর ইউটিউব চ্যনেলের নাম যেন এক হয়, আর না হলে চ্যনেলের নামটি মেইলে বলে দেবে, নইত কমেন্টে, আর যদি ইনবক্স এ না পাও তবে স্পাম এ মেইল পাবে, আর বাকি কাজ গুলো করতে ভুলবেনা! everycircuit link chrome link. http://everycircuit.com/app Play store link, https://play.google.com/store/apps/details?id=com.everycircuit.free Native Client enabled link. chrome://flags/#enable-nacl
K-150 pic programmer, Who will buy it or who will not buy it??
K-150 pic programmer,
Who will buy it or who will not buy it,
its support win 7 from under windows version,
but no support win 10,
W1209 Temperature Controller P0 to P6, Full Function Review.
W1209 Temperature Control Switch. SPECIFICATION: Temperature Control Range: -50 ~ 110 C Resolution at -9.9 to 99.9: 0.1 C Resolution at all other temperatures: 1 C Measurement Accuracy: 0.1 C Control Accuracy: 0.1 C Refresh Rate: 0.5 Seconds Input Power (DC): 12V Measuring Inputs: NTC (10K 0.5%) Waterproof Sensor: 0.5M Output: 1 Channel Relay Output, Capacity: 10A Settings Chart Long press the “SET” button to activate the menu. Code Description Range Default Value P0 Heat C/H C P1 Backlash Set 0.1-15 2 P2 Upper Limit 110 110 P3 Lower Limit -50 -50 P4 Correction -7.0 ~ 7.0 0 P5 Delay Start Time 0-10 mins 0 P6 High Temperature Alarm 0-110 OFF Long pressing +- will reset all values to their default Displaying the current temperature: The thermostat will display the current temperature in oC by default. When in any other mode making no input for approximately 5 seconds will cause the thermostat to return to this default display. Setting the trigger temperature: To set the trigger temperature press the button marked 'SET'. The seven segment display will flash. You can now set a trigger temperature (in oC) using the '+' and '-' buttons in 0.1 degree increments. If no buttons are pressed for approximately 2 seconds the trigger temperature will be stored and the display will return back to the current temperature. Setting the cooling or heating parameter P0: The parameter P0 has two settings, C and H. When set to C (default) the relay will energise when the temperature is reached. Use this setting if connecting to an air-conditioning system. When set to H the relay will de-energise when the temperature is reached. Use this setting if controlling a heating device. Setting the hysteresis parameter P1: This sets how much change in temperature must occur before the relay will change state. For example if set to the default 2oC and the the trigger temperature has been set to 25oC, it will not deenergise until the temperature falls back below below 23oC. Setting this hysteresis helps stop the thermostat from continually triggering when the temperature drifts around the trip temperature. Setting the upper limit of the thermostat parameter P2: This parameter limits the maximum trigger temperature that can be set. It can be used as a safety to stop an excessively high trigger temperature from accidentally being set by the user. Setting the lower limit of the thermostat parameter P3: This parameter limits the minimum trigger temperature that can be set. It can be used as a safety to stop an excessively low trigger temperature from accidentally being set by the user. Setting temperature offset correction parameter P4: Should you find there is a difference between the displayed temperature and the actual temperature (for instance if the temperature probe is on a long run of cable) you can make minor corrections to the temperature reading with this parameter. Setting the trigger delay parameter P5: This parameter allows for delaying switching of the relay when the trigger temperature has be reached. The parameter can be set in one minute increments up to a maximum of 10 minutes. Setting the high temperature alarm parameter P6: Setting a value for this parameter will cause the relay to switch off when the the temperature reaches this setting. The seven segment display will also show '---' to indicate an alarm condition. The relay will not re-energise until the temperature falls below this value. The default setting is OFF.
Thursday 30 April 2020
LOGO Soft Comfort-V8.2.1 32bit 64 bit Download Siemens Software.
LOGO is a small PLC of Siemens! It can be programmed directly but most people program with software because it is both easy and fast
Today ! I share specialized programming software for LOGO supporting Win 10 Win 7 , 8 ,
LOGO Soft Comfort-V8.2.1
Installation instructions::::
Step 1 : Extract the downloaded software
Step 2 : First Install LOGO Soft Comfort V7
Select Install to install the LOGO! Soft Comfort V7
Install USB Cable Driver
Step 3 : Open Software LOGO Soft Comfort V7 and Exit (at least 1 time ----- can run the V8.2.1 update file )
Step 4 : Install file Setup Logo!Soft Comfort Upgrade V8.2.1
Step 5 : Choose I accept the terms of the License Agreement then Next
Step 6 : Choose Next
Step 7 : Select Install Upgrade LOGO! Soft Comfort V8.2.1 version
Step 8 : The software installation process will take place very quickly
Step 9 : Select OK to install USB-PC Cable Driver
Step 10 : Select Done to finish the installation
We have the LOGO! Soft Comfort V8.2.1 software
Link Download Software
Wednesday 1 January 2020
Subscribe to:
Posts (Atom)
